#Processing moon in registax 6 tutorial movie
#Processing moon in registax 6 tutorial update
#Processing moon in registax 6 tutorial software
#Processing moon in registax 6 tutorial free

In the video I go through all the parts of AutoStakkert that I understand, or think I understand. You may need to add an align point or two to make sure you have every bit covered. Keep trying different sizes until you end up with between 10 and 20 align points. Check the Replace check box so every time you press the Place AP grid button it will start from scratch. Putting these into Registax V6.1.0.8 and clicking 'Set Alignpoints' to auto select the points produced 1799 points and then going to Stack produce the ghosting of the images. If youРІР‚в„ўre new to AutoStakkert then here is what works for me. Now the moon in these shots slowly moves from top right of the frame to the bottom left of the frame (my tracking motor on my EQ Platform not that accurate over 10mins). You must have some align points (APs) before button #3 is enabled. Then you push button #2, wait, but then button #3 is still disabled.

#Processing moon in registax 6 tutorial movie

After pushing button #1 you select your movie file and then button #2 becomes enabled. This thread on Cloudy Nights is all about AS!3.Р”Р„utoStakkert is fairly easy to use. He will see your questions on Cloudy Nights and the Yahoo Group but hopefully someone else will answer your question so Emil can spend his time making AS!3 even more awesome.Р”Р„utoStakkert!3 is now out. The author of AutoStakkert, Emil Kraaikamp, still actively supports AS!3 and new versions come out periodically. There is also an AutoStakkert Yahoo Group you can join.

#Processing moon in registax 6 tutorial free

Feel free to ask a question there or create a new post on the forum. You can read through it and find lots of helpful advice. There you can find this long running thread dedicated to AutoStakkert. There is a Solar System Imaging & Processing forum on Cloudy Nights. If you need help with AutoStakkert there are plenty of options. The wavelet processing capability of RegiStax 6 is amazing.

#Processing moon in registax 6 tutorial software

Many people then use RegiStax for the processing step and possibly other image processing software as well. Most everyone doing planetary imaging will recommend that you use AS!3 for stacking. Then came AutoStakkert which is easier to learn and does a better job at stacking but that is all it does. RegiStax will do both the stacking and processing steps. In the beginning there was only RegiStax.

The stacking software will discard the low quality frames in your movie file and align the remaining images and more or less take the average of them. Linux and OSX users are required to use Wine in so far as Registax is only available for Windows.For stacking software there are two popular choices: RegiStax 6 and AutoStakkert!3 (aka AS!3). NoteР’В : This tutorial is only valid for Windows users. Registax is then used to perform a precise alignment of the cropped picture set, stack everything into a single image, and apply the powerful wavelet filter. This preliminary step allows to reduce the size of the images aligned and stacked later by Registax which will perform faster (and often better). Ninox is used for a quick preliminary crop of the raw images, with an automatic centering of the brightest object in the frame (here it's the moon).

Focal lengthР’В : 400mm (35mm equivalent: 600mm).

In the following, the raw moon pictures have been acquired with a SONY SLT-A55 DSLR combined with a SIGMA 120-400 lens and the following settings: good for planets/moon based on the centre of gravity in each image.

#Processing moon in registax 6 tutorial update

The alignment task (before being able to properly stack the images) is mandatory in order to compensate the for relative the motion of the moon in front of the camera between the successive shots. REGISTAX (Paul MaxonРІР‚в„ўs tutorial) letting Registax 6 selecting them and I find that Registax 6 does a better job 70-75 on Jupiter and 150-200 on the moon or The 1st update of RegiStax 6 is available for download from the downloadpage. This post-processing task requires having a set of photographs (typically 10 to 100 for the moon) that have been acquired in the same conditions, with the same gears, and the same settings (focal length, f number, exposure time, ISO, white balance). Align and stack multiple moon shots (or planetary shots like Jupiter for example) allows to improve the final image quality (less noise, less deformations).